- 您现在的位置：买卖IC网 > Sheet目录1233 > NB7L32MMNEVB (ON Semiconductor)BOARD EVAL FOR NB7L32MM
NB7L32MMNEVB
Setup (continued)
Step 3: Setup Input Signals
3a: Set the signal generator amplitude to 400 mV.
NOTE: The signal generator amplitude can vary from
75 mV to 900 mV to produce a 400 mV DUT
output.
3b: Set the signal generator offset to ? 200 mV (the center of
a nominal NCML output).
NOTE: The V CMR (Input Common Mode Range) allows
the signal generator offset to vary as long as
V TH is within the V CMR range. Refer to the
device data sheet for further information.
Set the generator output for a PRBS data signal, or for a
square wave clock signal with a 50% duty cycle.
Step 4: Connect Output Signals
4a: Connect the outputs of the device (Q0, Q1, … ) to the
oscilloscope. The oscilloscope sampling head must have
internal 50 W termination to ground.
NOTE: Where a single output is being used, the
unconnected output for the pair must be
terminated to V CC through a 50 W resistor for
best operation. Unused pairs may be left
unconnected.
MORE INFORMATION ABOUT EVALUATION BOARD
Design Considerations for >10 GHz operation
While the NB7L32M is specified to operate at 10 GHz,
this evaluation board is designed to support operating
frequencies up to 20 GHz.
The following considerations played a key role to ensure
this evaluation board achieves high ? end microwave
performance:
? Optimal SMA connector launch
? Minimal insertion loss and signal dispersion
? Accurate Transmission line matching (50 W )
? Distributed effects while bypassing and noise filtering
http://onsemi.com
3
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
NB7N017MEVB
BOARD EVAL BBG NB7N017MMN
NC2003SR
STAND NOTEBOOK W/2FANS USB
NCN9252MUGEVB
BOARD EVALUATION NCN9252MU
NCP1031POEEVB
BOARD EVAL NCP1031 POE DC CONV
NCP1605LCDTVGEVB
BOARD EVAL NCP1605/1396
NCP1608BOOSTGEVB
BOARD EVAL NCP1608 100W BOOST
NCP1631PFCGEVB
BOARD DEMO NCP1631 INTERLEAV PFC
NCP1650EVB
BOARD EVAL NCP1650 PFC CTLR
相关代理商/技术参数
NB7L32MMNG
功能描述:时钟驱动器及分配 DIV BY 2 W/CML OUT RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel
NB7L32MMNR2G
功能描述:时钟驱动器及分配 DIV BY 2 W/CML OUT RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel
NB7L572
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:2.5V / 3.3V Differential 4:1 Mux Input to 1:2 LVPECL Clock/Data Fanout / Translator
NB7L572MNG
功能描述:时钟驱动器及分配 TSMC 4-1-2 MLL-PECL RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel
NB7L572MNR4G
功能描述:时钟驱动器及分配 TSMC 4-1-2 MLL-PECL RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel
NB7L585
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:2.5V / 3.3V Differential 2:1 Mux Input to 1:6 LVPECL Clock/Data Fanout Buffer / Translator
NB7L585MNG
功能描述:时钟驱动器及分配 2.5/3.3V DIFF MUX RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel
NB7L585MNR4G
功能描述:时钟驱动器及分配 2.5/3.3V DIFF MUX RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel